Open Seams In Hardwood Flooring

By Robert Robillard on Flooring, How To

Oak Floor Installed Parallel with Plank Subfloor – Results In Seams

I recently looked at a house for sale with Oak floors. The second I walked into the house I noticed multiple open seams in the hardwood flooring. The weird part was that these seams were evenly spaced approximately every 7 to 8 inches. The reason for these consistent and uniform seams is MOST likely caused by installing the hardwood floor in the same direction as the plank subfloor. When the old plank boards expand and contract, they take the hardwood boards with then – resulting in seams.

Another cause of open seams in hardwood flooring is called side bonding. Side bonding occurs from waterbased finish contributing to the gaps. Early on the waterbased finish didn’t have a sealer to go with it.

Installation of Hardwood Flooring Over Plank Subfloor

If you’re laying a new wood floor over an old plank subfloor, there are several things you need to take into consideration.

Plank subfloors are usually made up of 3/4″ thick x 6-8″ wide Southern Yellow Pine boards. This type of sub-flooring is usually found in older homes and can loosen up over time from the boards expanding and contracting.

Open Seams In Hardwood Flooring

4 Tips For Preventing Open Seams in Hardwood Flooring

  1. Allow your new flooring to acclimate to its new location, humidity levels.
  2. Allow for expansion and contraction of your new flooring by leaving an expansion gap of 10-15mm around your whole room.
  3. Install your hardwood flooring perpendicular to the subfloor plank boards
  4. If the sub-floor is in poor condition, or you need to run the hardwood floor in the same direction, install a plywood subfloor.

Install Hardwood Flooring Perpendicular To Subfloor

3/4″ thick Solid Wood Flooring must be installed across the subfloor boards (at a 90-degree angle). If the hardwood flooring is installed parallel to the direction of the plank subfloor the new wood floors could pull apart leaving open gaps if the underlayment planks expand/contract or the edges cup upwards.

It is very important to remember to re-secure the plank subfloor boards to the floor joists using 2-1/2″ deck screws or ring-shank nails. this will help prevent annoying squeaks.

Running Hardwood Flooring Parallel

If you have to run the wood flooring parallel with the subfloor boards you must install an additional layer of 3/8″ or 1/2″ thick plywood underlayment glued and screwed down over the plank subfloor.

Engineered, and 1/2″ Thick Flooring

Engineered flooring or flooring less than 1/2″ thick can be installed over a wood plank subfloor as long as the 3/4″ plank subfloor is flat. The hardwood flooring must be installed crossing the subfloor boards (90-degree angle).

Dealing with Deflection and Poor Subfloor Conditions

If there is any deflection in the subfloor when walked on it would be advisable to add an additional layer of 3/8″ or 1/2″ thick plywood underlayment glued and screwed down over the wood plank subfloor to add stability to weak subfloors. Doing this will also allow you to run your new wood flooring in any direction desired.

Don’t Forget To Install Rosin Paper

Rosin paper is designed to help with squeaks between the subfloors, but you are better off fixing the squeaks before installing the flooring.

 

 

If you enjoyed this post, make sure you subscribe to my RSS feed!

About the author

Robert Robillard

Carpenter / Remodeler / Editor

Rob Robillard is “The Concord Carpenter” Rob is a builder, general contractor, carpenter, woodworker, and editor of Concord Carpenter and ToolBoxBuzz As a General Contractor and carpenter, Rob owns and operates Concord Carpenter LLC. A full-service remodeling and construction company. Rob is a recognized leader in home building best practices and a source for how-to information for building professionals. On this website, Rob covers all aspects of home construction, building science, home improvement, woodworking, remodeling, and some of the best product and tool reviews. Rob is in charge of our Tool and Product Review series - Concord Carpenter Videos where we post all of our tool reviews and video tutorials. Rob approaches remodeling and building construction with a pragmatic and problem-solving approach. He enjoys using his knowledge and experience to help and educate building professionals as well as DIYers on best practices in the construction and remodeling industry. He's a strong advocate for "raising the bar" in the construction trades and promoting the trades to youth. #BeAMentor #Green2Great Craftsmanship, quality, and pride guide his journey on this channel The Concord Carpenter's motto: "Well done is better than well said!" : Read more about Rob

All posts by Robert »

Not what you're looking for?

Search for more articles here. Enter keywords like roof leak, bookcase, deck, etc to find your topic.

© Copyright 2019 A Concord Carpenter · All Rights Reserved