How to Eliminate Squeaks In Hardwood Floors

By Robert Robillard on How To

Installing Hardwood FlooringFloor Squeaks

Hi Rob Thanks for all the great info in your column, website and newsletters. I would appreciate advice on how to eliminate squeaks in hardwood floors.

Our fairly standard oak floors seem to get more squeaky spots with time. Is there a way to fix them – do we nail or screw down those spots?  Thanks, Marla

Hi Marla,

I has a similar problem many years ago and I installed new slats coupled with mid-span supports. I used cut off 4×4 and installed them in the middle of the slats to support the mid-span. Worked like a charm

I personally enjoy my 1863 floor squeaks as it alerts me when my teenagers are home!!  My guess is that your floor is nailed through the tongue [hidden fastener] and either the nails are loosening up, were too short or the sub-floor below is loose.

I’d hate to see you install face nails or fasteners in a finished oak floor, these repairs are BEST done from below, unless you have carpet.

How to Eliminate Squeaks In Hardwood FloorsWhat Causes Squeaks

Squeaks are often caused by movement and rubbing of in wood seams such as sub-flooring sheets or boards, friction in tongue and groove or ship-lap flooring.

If you can stop the movement and you stop squeak, but that is easier said than done. If the floor joists below are exposed you can inspect the areas that seem to squeak the worst first. I wish I knew what type of sub-floor you have because it would dictate my approach.

How to Eliminate Squeaks In Hardwood FloorsPlywood Sub-floor:

If you have a plywood floor, squeaks over a joist are best silenced from top fasteners, although a repair from underneath the floor is cosmetically more appealing.   Squeaks between the joists in the plywood seams are best silenced by installing blocking under the seam, and fastened to the two floor joists.

In this case I would install a liberal amount of construction adhesive to the top edge of my blocking and ensure a snug fit up against the sub-floor when securing the two adjacent joists. Screw the block to the joist first, then install a screw through the block and into floor – to pull it down. Have someone stand on the area while doing this to apply downward pressure.

How to Eliminate Squeaks In Hardwood FloorsWood Strip Sub-Flooring:

Blocking works well here too. Installing a screw on an angle through the joist and into the floor. Try to get some construction adhesive along the joist on both sides of the squeak while the floor is raised, to allow some adhesive to enter the crack between floor and joist. Again, have someone stand over the area for downward pressure.

Be careful not to use too long a screw or penetrate too far so your screw penetrates through the floor above. That is a rookie mistake and we’ll have you sit in the truck for the rest of the work day! I’d be lying if I told you I didn’t learn that the hard way! J

Commercially Sold Metal Brackets:

There are also metal brackets sold commercially that reduce or eliminate squeaks. I’ve never used them but they do appear to require minimal skill to install.

They usually consist of some sort of metal angled base used in conjunction with screws to pull the floor in tightly against the joist.

If you choose this route I would still deploy construction adhesive at the floor and joist junction.

Fasteners from Top Down:

This would be my last resort approach, and is BEST done before you refinish your floors. You can install trim screws in inconspicuous areas, but the squeaks always seem to be on the path most traveled! Alternatively, you can install these screw with wood plugs, and then refinish the floor.

If you enjoyed this post, make sure you subscribe to my RSS feed!

About the author

Robert Robillard

Carpenter / Remodeler / Editor

Rob Robillard is “The Concord Carpenter” Rob is a builder, general contractor, carpenter, woodworker, and editor of Concord Carpenter and ToolBoxBuzz As a General Contractor and carpenter, Rob owns and operates Concord Carpenter LLC. A full-service remodeling and construction company. Rob is a recognized leader in home building best practices and a source for how-to information for building professionals. On this website, Rob covers all aspects of home construction, building science, home improvement, woodworking, remodeling, and some of the best product and tool reviews. Rob is in charge of our Tool and Product Review series - Concord Carpenter Videos where we post all of our tool reviews and video tutorials. Rob approaches remodeling and building construction with a pragmatic and problem-solving approach. He enjoys using his knowledge and experience to help and educate building professionals as well as DIYers on best practices in the construction and remodeling industry. He's a strong advocate for "raising the bar" in the construction trades and promoting the trades to youth. #BeAMentor #Green2Great Craftsmanship, quality, and pride guide his journey on this channel The Concord Carpenter's motto: "Well done is better than well said!" : Read more about Rob

All posts by Robert »

Not what you're looking for?

Search for more articles here. Enter keywords like roof leak, bookcase, deck, etc to find your topic.

© Copyright 2019 A Concord Carpenter · All Rights Reserved